Сервер Red Hat Linux 7.3
Настройки устройств сервера elis.it.ru
Файл настройки клавиатуры /etc/sysconfig/keyboard
[root@elis root]# less /etc/sysconfig/keyboard KEYBOARDTYPE="pc" KEYTABLE="ru"
Файл настройки HardWare
[root@elis root]# less /etc/sysconfig/hwconf - class: OTHER bus: PCI detached: 0 driver: agpgart desc: "Intel Corporation|440BX/ZX - 82443BX/ZX Host bridge" vendorId: 8086 deviceId: 7190 subVendorId: 0000 subDeviceId: 0000 pciType: 1 - class: OTHER bus: PCI detached: 0 driver: ignore desc: "Intel Corporation|440BX/ZX - 82443BX/ZX AGP bridge" vendorId: 8086 deviceId: 7191 subVendorId: 0000 subDeviceId: 0000 pciType: 1 - class: OTHER bus: PCI detached: 0 driver: unknown desc: "Intel Corporation|82371AB PIIX4 ISA" vendorId: 8086 deviceId: 7110 subVendorId: 0000 subDeviceId: 0000 pciType: 1 - class: OTHER bus: PCI detached: 0 driver: unknown desc: "Intel Corporation|82371AB PIIX4 IDE" vendorId: 8086 deviceId: 7111 subVendorId: 0000 subDeviceId: 0000 pciType: 1 - class: OTHER bus: PCI detached: 0 driver: unknown desc: "Intel Corporation|82371AB PIIX4 ACPI" vendorId: 8086 deviceId: 7113 subVendorId: 0000 subDeviceId: 0000 pciType: 1 - class: OTHER bus: USB detached: 0 driver: unknown desc: "USB UHCI Root Hub" usbclass: 9 usbsubclass: 0 usbprotocol: 0 usbbus: 1 usblevel: 0 usbport: 0 vendorId: 0000 deviceId: 0000 productrevision: unknown - class: NETWORK bus: PCI detached: 0 device: eth driver: 3c59x desc: "3Com Corporation|3c905B 100BaseTX [Cyclone]" vendorId: 10b7 deviceId: 9055 subVendorId: 10b7 subDeviceId: 9055 pciType: 1 - class: CDROM bus: IDE detached: 0 device: hdc driver: ignore desc: "MATSHITA CR-594" - class: VIDEO bus: PCI detached: 0 driver: Card:ATI Mach64 desc: "ATI|3D Rage LT Pro AGP-133" vendorId: 1002 deviceId: 4c42 subVendorId: 1002 subDeviceId: 0044 pciType: 1 - class: HD bus: IDE detached: 0 device: hda driver: ignore desc: "FUJITSU MPF3102AT" physical: 19857/16/63 logical: 1245/255/63 - class: USB bus: PCI detached: 0 driver: usb-uhci desc: "Intel Corporation|82371AB PIIX4 USB" vendorId: 8086 deviceId: 7112 subVendorId: 0000 subDeviceId: 0000 pciType: 1
Файл настройки жестких дисков (винчестеров)
[root@elis /root]# less /etc/sysconfig/harddisks # These options are used to tune the hard drives - # read the hdparm man page for more information # Set this to 1 to enable DMA. This might cause some # data corruption on certain chipset / hard drive # combinations. This is used with the "-d" option # USE_DMA=1 # Multiple sector I/O. a feature of most modern IDE hard drives, # permitting the transfer of multiple sectors per I/O interrupt, # rather than the usual one sector per interrupt. When this feature # is enabled, it typically reduces operating system overhead for disk # I/O by 30-50%. On many systems, it also provides increased data # throughput of anywhere from 5% to 50%. Some drives, however (most # notably the WD Caviar series), seem to run slower with multiple mode # enabled. Under rare circumstances, such failures can result in # massive filesystem corruption. USE WITH CAUTION AND BACKUP. # This is the sector count for multiple sector I/O - the "-m" option # # MULTIPLE_IO=16 # (E)IDE 32-bit I/O support (to interface card) # # EIDE_32BIT=3 # Enable drive read-lookahead # # LOOKAHEAD=1 # Add extra parameters here if wanted # On reasonably new hardware, you may want to try -X66, -X67 or -X68 # Other flags you might want to experiment with are -u1, -a and -m # See the hdparm manpage (man hdparm) for details and more options. # EXTRA_PARAMS=
Файл настройки файловой системы
[root@elis /root]# less /etc/fstab LABEL=/ / ext2 defaults 1 1 none /dev/pts devpts gid=5,mode=620 0 0 LABEL=/data /data ext2 defaults 1 2 none /proc proc defaults 0 0 none /dev/shm tmpfs defaults 0 0 LABEL=/usr /usr ext2 defaults 1 2 /dev/hda3 swap swap defaults 0 0 /dev/cdrom /mnt/cdrom udf,iso9660 noauto,owner,kudzu,ro 0 0 /dev/fd0 /mnt/floppy auto noauto,owner,kudzu 0 0